Advertising
EasyTouch Wireless Control Panel Installation and User’s Guide EasyTouch Wireless Control Panel Kit Contents The following items are included in the EasyTouch wireless control panel kit. If any items are missing please contact Pentair Technical Support (see page vi). † EasyTouch wireless control panel † Four AA-size alkaline batteries. EasyTouch® 8 and 4 Pool and Spa Control System Kit Contents The following items are included in the EasyTouch ® 8 and EasyTouch 4 control system kit which may also include the IntelliChlor cell. † EasyTouch control panel (mounted in the load center) † EasyTouch load center enclosure. Pentair 520547 EasyTouch Wireless Controller Kit For 8 Circuit System, Including Tranceiver. 3.4 out of 5 stars 15. $645.00 $ 645. Pentair Pool Products 521885 Easy Touch Is4 Spa Side Remote Control System. 4.9 out of 5 stars 7. $206.24 $ 206. 24 $215.00 $215.00. Get it as soon as Wed, Nov 20. PoolSupplyWorld carries all of the well-known brands in the pool and spa supply industry, as well as innovative new manufacturers. Our goal is to make your swimming pool and spa inviting and healthy by offering a selection of tens of thousands of products and parts for every imaginable need. Pentair EasyTouch 8 and 4 Pool and Spa Control System User Manual. Equipment location. Pentair Remote control. Manuals Directory ManualsDir.com - online owner manuals library. Pentair manuals. Remote control. EasyTouch 8 and 4 Pool and Spa Control System.
17
EasyTouch Load Center Installation Guide
Installing and Connecting Temperature Sensors
Water Temperature Sensor
To install the water sensor:
1. Drill a 5/16 in. hole in the plumbing between the filter pump and filter.
2. Insert tip of sensor into the hole. Use the band clamp to secure the sensor to the pipe.
Tighten the clamp just enough so that the o-ring begins to flatten. Do not overtighten
3. At the EasyTouch load center, route the wire up through the low voltage raceway to the
motherboard.
4. Fasten the cable to the plumbing with cable ties.
5. Cut off the excess wire and the strip conductors ¼ inch. Insert the wires into the WATER
screw terminals (J21) on right-side of the motherboard. For motherboard connection details,
refer to “EasyTouch Motherboard Connections,” on page 13. For wiring details, refer to
EasyTouch System Wiring Diagram,” on page 23.
refer to “EasyTouch Motherboard Connections,” on page 13. For wiring details, refer to
EasyTouch System Wiring Diagram,” on page 23.
Ambient Air Temperature (Freeze Protection) Sensor
To install the air sensor:
1
Mount the sensor in the open air, in a shaded area, away from air conditioners. During the
winter months, to avoid freeze damage to pool and spa equipment, mount the air sensor in a
shaded area to assure proper temperature readings.
shaded area to assure proper temperature readings.
Pentair Easytouch Wireless Controller Manual
2
Route the wire through the low voltage raceway to the motherboard.
3
Fasten the cable to the plumbing with cable ties.
4
Cut off the excess wire and the strip conductors ¼ in. Insert the wires into the AIR screw
terminals (J21) on right side of the motherboard.
Solar Temperature Sensor (Optional)
To install the solar sensor:
1
Mount the sensor on a flat surface, with the same exposure to sun as the solar collectors
(next to the collectors is recommended). Do not let the sensor touch the panels.
2
If necessary, splice a two-conductor extension wire to the sensor. Route the wire to the load
center and up through the low voltage raceway to the motherboard.
3
Strip the conductors ¼ in. Insert the wires into the SOLAR screw terminals (J21) on right
side of the motherboard.
Advertising
Popular Brands
Popular manuals
Advertising
iii
EasyTouch Load Center Installation Guide
IMPORTANT SAFETY PRECAUTIONS
(Continued)
WARNING
To reduce the risk of injury, do not permit children to use this product unless they
are closely supervised at all times.
are closely supervised at all times.
WARNING
The use of alcohol, drugs, or medication can greatly increase the risk of
fatal hyperthermia in hot tubs and spas.
fatal hyperthermia in hot tubs and spas.
WARNING
Control System is intended to control heaters with built-in high limit circuits ONLY.
Failure to do so may cause property damage or personal injury.
Failure to do so may cause property damage or personal injury.
WARNING
Do not use this product to control an automatic pool cover. Swimmers may
become entrapped underneath the cover.
become entrapped underneath the cover.
WARNING
For units intended for use in other than single-family dwellings, a clearly labeled
emergency switch shall be provided as part of the installation. The switch shall
be readily accessible to the occupants and shall be installed at least
10 feet (3.05 m) away, adjacent to, and within sight of, the unit.
emergency switch shall be provided as part of the installation. The switch shall
be readily accessible to the occupants and shall be installed at least
10 feet (3.05 m) away, adjacent to, and within sight of, the unit.
CAUTION
Except for listed spa-side remote controls, install a minimum of five (5) feet from
the inside wall of the pool and spa.
the inside wall of the pool and spa.
FCC Standard
- 47 CFR Part 15, Subpart C (Section 15.247). This version is limited to chapter 1
to chapter 11 by specified firmware controlled in the U.S.A.
Canada - Industry Canada (IC)
- The IntelliChlor device complies with RSS210 of Industry
Canada. (1999). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Instruction to user - The IntelliChlor device has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. The IntelliChlor device
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by switching the device off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. The IntelliChlor device
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by switching the device off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Pentair Ez Touch Manual
Note: The user is cautioned that changes and modifications made to the IntelliChlor device without
the approval of the manufacturer could void the user’s authority to operate this equipment.
the approval of the manufacturer could void the user’s authority to operate this equipment.
Advertising
Popular Brands
Popular manuals